CMC (T-H Marine ) High Speed Hydraulic Power-Lift Transom Jacks PL65
CMC PL-65 High Speed Jack Plate
CMC 65302 PL-65 HS 5 1/2" Setback No Gauge
CMC 65301 PL-65 HS 5 1/2" Setback with Gauge
CMC 61301 PL-65 HS 10" Setback with gauge
CMC 61302 PL-65 HS 10"setback no gauge
Full stroke in 8 seconds.
Features Of Patented Hydraulic Power-Lift® (U.S. Patent 4,482,330):
Made of 6061 T6 alloy aluminum extrusions and fastened with stainless steel fasteners. Ideal for fresh or salt water use. No welds or castings to break.
The dependable, self-contained and water proof hydraulic actuator has a maximum lifting capacity of 7853 pounds of thrust. More than any other transom jack. You will have no problem lifting even a V-6 300 hp max. motor at full throttle.
The hydraulic actuator is mounted inside the structure of the Power-Lift, yet it is fully accessible without removing the engine. There are no hoses to contain, nor will you have to contend with mounting a pump and reservoir inside your boat, as is the need with other transom jacks. The hydraulic actuator is completely self-contained with its own fluid reservoir (eliminates the need for hydraulic tank and hoses inside the boat). It contains a permanent magnet motor for more power and constant torque. The cylinder within the actuator has twice the lifting capacity than other transom jacks on the market. It contains a no-leak seal and wiper that keeps dirt and water out of the working parts. The system is made of 100% non-ferrous material which makes it impervious to saltwater and freshwater.
The patented roller design means less friction, longer wear, less maintenance, and virtually no binding problems which are common with other transom jacks. The roller assembly contains a stainless steel 3/4" pin with aluminum-bronze alloy rollers. The roller is highly impact resistant, corrosive resistant, and has a high load carrying capacity. This patented design virtually eliminates any chance of binding which is common with other transom jacks.
The PL-65 is rated for V-6 motors and smaller and gives you 5" of vertical travel with 1-1/2" of adjustment on the motor bracket and 1-1/2" of adjustment on the transom bracket. A total of 8” of possible adjustment.
***NEW***
INTRODUCING THE NEW HIGH SPEED POWER-LIFT FROM CMC the PL65HS
Cook Mfg. Corp. (CMC) of Duncan. OK. introduces the High Speed Power-Lift as the newest addition to their product line.
Features Of Patented Hydraulic High Speed Power-Lift® Full Stroke in 8 seconds! (U.S. Patent 4,482,330)
1. The PL-65HS is made of 3/4 and 1/2 inch 6061 T6 alloy aluminum extrusions and fastened with stainless steel fasteners. Ideal for fresh or salt water use. No welds or castings to break.
2. The dependable self contained and water proof high speed hydraulic actuator has a max. lifting capacity of 4417 pounds of thrust. You will have no problem lifting even a V-6 300 hp max. motor at full throttle. The hydraulic actuator is mounted inside the structure of the PL-65HS Power-Lift, yet it is fully accessible without removing the engine. All PL65's have are no hoses to contain, nor will you have to contend with mounting a pump and reservoir inside your boat, as is the need with other transom jacks. The hydraulic actuator is completely self-contained with its own fluid reservoir (eliminates the need for hydraulic tank and hoses inside the boat). It contains a permanent magnet motor for more power and constant torque. The cylinder within the actuator has more lifting capacity than other transom jacks on the market. It contains a no-leak seal and wiper that keeps dirt and water out of the working parts. The system is made of 100% non-ferrous material which makes it impervious to saltwater and freshwater.
3. The patented roller design means less friction, longer wear, less maintenance, and virtually no binding problems which are common with other transom jacks. The roller assembly contains a stainless steel 3/4" pin with aluminum-bronze alloy rollers. The roller is highly impact resistant, corrosive resistant, and has a high load carrying capacity. This patented design virtually eliminates any chance of binding which is common with other transom jacks.
The PL-65 HS is rated for V-6 motors and smaller and gives you 5" of vertical travel with 1-1/2" of adjustment on the motor bracket and 1-1/2" of adjustment on the transom bracket. A TOTAL OF 8" OF POSSIBLE ADJUSTMENT! It also can be purchased with stainless steel motor rails, Model PL-65SS (for V-8 motors 300 HP MAX).
Also available the standard CMC Power-Lift PL65 jack plate can improve the performance of virtually any type outboard. This unique outboard motor hydraulic lifting device works independently of your power trim and tilt to allow the boat-motor-prop combination to work at it's maximum efficiency. The Power-Lift jack plate gives you the ability to adjust your motor down, for better out of the hole shots or up for better top end speed, better fuel efficiency, and more prop clearance in shallow water. With the touch of a switch the Power-Lift makes it easy to find that optimum height for any condition while underway at full speed! Ideal for ski, bass, or work boats. In order for your outboard to perform at its full potential and efficiency, it should be adjusted to different heights at different speeds, water conditions and loads in your boat. The CMC Jack Plate Power-Lift PL-65 jack plate will set your motor back away from the transom 5 1/2 inches which allows the prop to run in "cleaner" water giving the prop a better "bite" and eliminating prop slippage. The system is made of 100% non-ferrous material which makes it impervious to saltwater and freshwater use.
Superior quality has made the Power-Lift PL65 Jack Plates are the #1 selling transom jack in the world! We have been manufacturing top quality transom jacks longer than most of our competitors have been in business. No short cuts are taken at CMC. Computer aided design and precision machining of the Power-Lift PL-65 is done totally at our facility so you can be sure to get the best quality transom jack at a very competitive price. The Power-Lift jack plate utilizes a totally waterproof 12 volt DC marine hydraulic system that is rated OVER 7800 Pounds of thrust. More lifting capacity than any other jack plate on the market. It is 40% more powerful and much more dependable than electro-mechanical transom jacks on the market. The motor bracket moves up and down on a transom bracket by use of rollers Machined from aluminum-bronze alloy. These rollers are highly impact resistant, Corrosive resistant, and have a high load carrying capacity. Thrust is eliminated by the stainless steel pin through this roller with a self lubricating non-metallic material (G.S.M. Nylatron) used for thrust guides on either side of the rollers. This feature eliminates any vibration or "shimmy" due to load applied from high powered outboards. This patented design virtually eliminates any chance of binding, which is common with other transom jacks.
PL65 Jack Plate - Superior Design And Construction