Jack Plate: Manual
JPM - MJ5h

Manual Jack Plate: Heavy Duty (5 inch )

Plate can be set at three different horizontal dimensions; 4 1/4 inch setback, 5 inch setback, to achieve optimum performance and handling (40 HP max)
Ultra Lightweight - Only 12 LBS.

Manual Jack Plate

Available in 8 inch Setback Jackplate #MJ8 and Heavy duty 5 inch Jackplate #MJ5

Also available for extreme conditions such as offshore racing #MJH.

Manual Jack
Overall Width= 17 7/8" - Overall Height= 14" - Weight= 19 lbs.

Jack Plate: Manual
JPM - MJ8

Manual Jack Plate: 8 inch Setback

Plate can be set at three different horizontal dimensions; 4 1/4 inch setback, 5 inch setback, to achieve optimum performance and handling (40 HP max)
Ultra Lightweight - Only 12 LBS.

Manual Jack Plate

Available in 8 inch Setback Jackplate #MJ8 and Heavy duty 5 inch Jackplate #MJ5

Also available for extreme conditions such as offshore racing #MJH.

Manual Jack
Overall Width= 17 7/8" - Overall Height= 14" - Weight= 19 lbs.

Jack Plate: Manual
JPM - MMJ

Manual Jack Plate: Mini Manual - Ultra Light weight only 12 lbs

Plate can be set at three different horizontal dimensions; 4 1/4 inch setback, 5 inch setback, to achieve optimum performance and handling (40 HP max)

Jack Plate: Manual-Convertible
JPC - MJ5-convertible

Convertible Jacking Plate -Multiple offsets and wedge - Converting the new 4 in 1 is as easy as dropping anchor!
5 inch Offset with 6degree wedge

"Designed to give maximum performance, speed and economy." Hold your mouse cursor over a jack plate description to see the drawing for that plate.

2 1/2 inch offset no wedge A feature which is used on the lightest of boats. Allowing the engine to be raised to its maximum height without putting the weight of the engine too far behind the transom which could create too much bow lift. 2 1/2 inch Offset with Negative 6-Degree Wedge This design can be used when the transom of a boat is too steep of an angle to allow the outboard motor to perform properly. For example: an 18-degree transom when this design is applied. 5-inch Offset No Wedge This option desirability will vary from one boat to another depending upon weight and length of boat. Some outboard motors have a limited trim angle and the 6-degree wedge may not allow for enough bow lift. By setting the plate at the no wedge design, it will give maximum bow lift. 5-inch Offset with 6-Degree Wedge Jacking bolts- allow motor to be moved to any height. No need to take boat out of the water. Offset- positions motor 5 1/2 inches behind transom. This allows prop to run in cleaner water, away from the turbulence and bubbles created by the hull. This helps stop slippage of prop, and helps stop torque in steering wheel at high speeds. Trim-In- this allows motor to be trimmed in or down 6 degrees more than if mounted flat on transom. Helps stop low speed porpoising. Balance load better. Light-weight- approximately 20lbs., constructed of aircraft grade aluminum and stainless steel. Anodized- anodized black finish to prevent corrosion. Anodize also lets paint stick to aluminum if painting is preferred. Narrow designed- only inches wide, make this plate possible to fit the narrowest of transoms. Fits V-6- pre-drilled to fit all late model V-6's. Can be modified to fit any size outboard. Converting the new 4 in 1 is as easy as dropping anchor! Adjustable plates turn 180 degrees and switch sides, then bolt in place.

Manual Jack Plate Available in 8 inch Setback Jack plate #MJ8 and Heavy duty 5 inch Jack plate #MJ5 Also available for extreme conditions such as offshore racing #MJH. Manual Jack Overall Width= 17 7/8" - Overall Height= 14" - Weight= 19 lbs.