PT-130 Hydraulic Tilt & Trim 13001 and 13002 PT130 Cook Manufacturing


	Accessories
	Banana Boats
	Barbeques
	Battery Chargers
	Barometers
	Binoculars
	Bilge Heaters
	Body Saver Mats
	Chargers
	Canoes
	Clocks
	Docking Systems
	Dock lights
	Fenders
	Fireplaces
	Fishing Boats
	Hatch Lifters
	Heaters
	Hunting
	Ice Fishing Shelter
	Inflatable Boats
	Inflatable Mattress
	Jack Plates
	Kayaks
	Keel Guard
	Ladders
	Mats
	Mooring Whips
	Navigation Software
	PaddleBuoy
	Pedal /Paddle Boats
	Pontoon Boats
	Power Steering
	Propellers
	Safety Products
	SailCat
	Spotlights
	Steering Wheels
	Steering Systems
	Stoves
	Tilt & Trim
	Trampolines
	Transom Jacks
	Trim Tabs
	Trolling Motors
	Wakeboard Racks
	Wakeboard Tower
	Water Skeeter
	Wall Heaters
	Wetsuits
	Winches

PT-130 Electric Hydraulic Tilt & Trim
Part # 13001 and 13002
For smaller engines click here for the PT-35
Also see accessories
Set Back Plates

90 Degrees Of Tilt And Trim !

Experience Convenience & Improved Performance

The CMC PT-130 Tilt & Trim incorporates a 6" setback which enhances Boat Stability and enables the prop to get a better "bite" at a higher prop setting. With the touch of a switch you can raise your motor to protect your prop from damage and your back from strain. The PT130 Tilt & Trim has 20 degrees of trim and 90 degrees of trim and tilt. It allows to tuck your motor in to get your boat on plane smoother and faster. When you're underway, you can change the angle of your motor to obtain the best performance for your load and water conditions. It gives you a more stable ride, increases top end speed, allows more prop clearance, and better fuel economy.

Superior Construction

The PT-130 Tilt and Trim, is a computer aided design, our commitment to quality and manufacturing excellence is evident in every product we make. The PT- 130 is constructed of 1/2" 6061 T6 alloy aluminum extrusions and fastened with stainless steel fasteners for maximum strength and durability. No molded aluminum which has less resistance to stress. This system is made of 100% non-ferrous material which makes it impervious to saltwater and freshwater.

Most Powerful On The Market

The PT-130 is actuated with a totally waterproof marine electric hydraulic System that is rated OVER 7800 lbs. OF THRUST! Over 40% more powerful than other brands. It is also more impervious to saltwater and freshwater than others because it is made of 100% non ferrous materials. Our hydraulic system is completely sealed and submersible and runs without worry of water damage. No electromechanical ball screw !

Ideal For Any Type Of Boat

The CMC PT130 will fit on virtually any type of boat and outboard motor. The PT-130 along with the optional trim gauge makes it very easy to know the exact angle of your motor. It's especially convenient on pontoon boats. Rated for 10H.P. through 130H.P. motors, it fits standard B.I.A. bolt pattern motors without drilling holes. A convenient adapter kit is available for motors that are mounted with transom clamps.

*Mounting Hardware Included With Every PT-130 Specifications

COMPARE OUR PRICES
For smaller engines click here for the PT-35

Also Click here
if your engine
is 35HP or less

Transom Spacer for Pontoon Boat (#13032)

The Transom on some pontoon boats are inset with an aluminum lip along the sides. To conveniently mount the PT-130 to this type transom, this transom spacer is available. The transom spacers are 1" thick allowing you to mount the PT130 without interference with the 1/2" to 3/4" lip around the transom on some pontoon boats.

Transom Clamp Motor Adapter (#13022)

For installation of motors mounted with transom clamps, an adapter kit is available from CMC. This adapter kit is made for quick and easy installation of these type motors. The photo above shows this adapter on a PT130 with a transom clamp motor.

For technical help contact the Help Desk